Sports TurfManager (877) 360-4657

Laying Artificial Turf Over Dirt or Soil

Turf can be unrolled on bare dirt, but it will not stay flat. Here is what happens to turf on raw soil and the base layers that prevent it. Planning a project? Start with our artificial turf installation guide.

Can you put turf over dirt? Physically, yes. You can unroll synthetic grass on a patch of bare soil, pin the edges and walk on it the same afternoon. The problem shows up over the next few months: the soil settles unevenly, water sits under the backing, the edges heave and the surface ripples like a rug on an uneven floor. The short-term shortcut becomes a surface that has to be lifted and rebuilt. Understanding how to lay synthetic turf on soil correctly means understanding why a professional artificial turf installation spends most of its labor on what is underneath the grass.

Quick answerDo not lay turf directly on dirt. Excavate 3 to 4 inches, install a weed barrier, build a compacted crushed-aggregate base topped with a thin layer of fines, grade it for drainage, then lay, stretch, seam and infill the turf. The base is what keeps the surface flat, firm and draining for the life of the turf.

How to lay synthetic turf on soil: why bare dirt does not last

Soil is alive and it moves. It expands when wet and shrinks when dry, settles under foot traffic, is tunneled by worms and insects and heaves in a hard frost. Natural grass copes because its roots knit the top layer together and it regrows over any disturbance. Synthetic turf has no roots. It simply follows whatever the ground beneath it does.

The specific failures of turf laid over dirt are predictable:

  • Settling. Foot traffic compacts soil unevenly, so paths become shallow troughs and the turf sags into them. Infill migrates to the low spots and the pile mats there.
  • Poor drainage. Turf backing is perforated, but water that passes through has nowhere to go if the soil beneath is clay or compacted. It pools under the turf, the backing stays wet, and the area smells and grows algae.
  • Rippling. Turf expands slightly in heat. On a firm base it is stretched and held tight by nails driven into compacted stone. On soil the nails loosen as the ground moves, and the turf slackens into wrinkles.
  • Weeds. Soil contains a seed bank. Without a barrier and a stone layer, weeds germinate under the turf and push up through the drainage holes.
  • Edge failure. Soil at a perimeter crumbles, nails pull out and the edge curls.

What a proper base includes

The job of the base is to replace the unpredictable top few inches of soil with a layer that is stable, compactable and porous. The standard residential build-up is below. Depths vary with climate and soil; frost-prone regions and heavy clay soils push toward the deeper end.

Layer (bottom to top)MaterialTypical depthPurpose
SubgradeNative soil, graded and compactedn/aStable platform with rough fall for drainage
Weed barrierWoven geotextile fabricn/aBlocks weeds, separates soil from stone
Sub-baseCrushed aggregate, 3/4 inch minus2 to 4 inchesStructure, load spreading, drainage
Leveling layerDecomposed granite or stone dust0.5 to 1 inchSmooth, compactable surface for the turf
TurfSynthetic grass with perforated backing1.25 to 2 inch pileThe visible surface
InfillSilica sand and/or rubber1 to 2 lb per sq ftHolds fibers upright, ballasts the turf

How to lay synthetic turf on soil, step by step

This is the sequence an experienced crew follows. It applies whether the area is a small side yard or a full backyard.

  1. Mark and excavateOutline the area, locate and protect irrigation lines and utilities, then remove sod and soil to a depth of 3 to 4 inches below the finished grade. Pull roots and rocks. Haul the spoil away; do not spread it where it will wash back.
  2. Grade and compact the subgradeRake the exposed soil to a slight fall, usually one to two percent away from structures, and run a plate compactor over it. Any soft spots are dug out and filled with aggregate, then geotextile weed fabric is laid over the subgrade with six-inch overlaps.
  3. Build the sub-base in liftsSpread aggregate in layers about two inches thick, wetting lightly and compacting each one before adding the next. Compacting a single thick layer only firms up the top; lifts are what make the base solid all the way down.
  4. Add and screed the leveling layerSpread fines, screed to the final grade with a long straightedge, mist with water and compact again. The surface should feel like a dirt road, firm enough that a footprint barely registers.
  5. Lay, relax and cut the turfUnroll the turf with all pieces running the same direction so the grain matches. Let it sit in the sun for a few hours, then cut to shape leaving a small overlap at edges.
  6. Seam and stretchJoin pieces over seaming tape with turf adhesive, pressing and weighting the join. Stretch the turf taut with a carpet kicker or stretcher and nail the perimeter every 4 to 6 inches with 5 or 6 inch non-galvanized spikes.
  7. Brush and infillPower-broom the pile upright, spread infill in several thin passes with a drop spreader, brushing between passes until the fibers stand and the infill sits just below the tips.

Pro tip: Compaction is the step DIYers skip or rush, and it is the one that determines whether the lawn is still flat in five years. Rent a plate compactor, not a hand tamper, and make at least three full passes per lift in alternating directions.

Talk to an installer who builds it right

Experienced local crews. Every line item in writing.

Special situations

Heavy clay. Clay drains slowly and holds water against the base. Deeper aggregate, a perforated drain pipe along the low edge or a layer of coarser clean stone under the minus aggregate may be needed. If a puddle on the bare clay takes more than a few hours to soak in, drainage needs design, not hope.

Hard surfaces. Turf over an existing patio, deck or rooftop is a different method using pads and adhesive instead of an aggregate base. Our page on balcony turf explains that approach.

Doing it right the first time

The base is most of the labor in a turf installation and is invisible when the job is done, which is why it gets skipped in rushed work. A lawn on a compacted aggregate base stays flat and drains in minutes; a lawn on dirt looks the same on day one and completely different by the second summer.

If you are planning a turf lawn and want ideas for layout once the base is in, browse our backyard turf ideas. When you are ready to talk to someone about the excavation, base and compaction your yard needs, the artificial turf installation crews we work with are chosen for exactly that groundwork.

Turf over dirt FAQ

Can you put turf over dirt without a base?

You can, but it will settle, ripple, drain poorly and grow weeds within a season. A compacted aggregate base is what makes synthetic turf a long-term surface.

How do you install artificial turf over dirt?

Excavate 3 to 4 inches, compact the soil, lay weed fabric, build a compacted crushed-stone base in lifts, screed a thin leveling layer, then lay, seam, stretch, nail and infill the turf.

How deep should the base be when laying turf over dirt?

Most residential lawns use 3 to 4 inches of compacted aggregate plus up to an inch of fines. Clay soils and cold climates with ground frost may need more.

The complete turf installation guide

What a quality install looks like, the eight installation steps, spec sheets, and how to choose an installer.

Read the guide
Call nowTalk to us